The Role of Aeration in Wastewater Treatment

Industrial wastewater treatment is the process used to treat wastewater that is produced as a by-product of industrial or commercial activities. After treatment, the treated industrial wastewater may be reused or released to surface water in the environment.
What is Aeration?
Wastewater aeration is the process of adding air into wastewater to allow aerobic bio-degradation of the pollutant components. It is an integral part of most biological wastewater treatment systems. Chemical treatments make use of chemicals to react and stabilize the contaminants in the wastewater stream whereas biological treatments use microorganisms that naturally occur in wastewater to degrade contaminants.
When is Aeration Used?
The activated sludge process is the most common option under the secondary treatment used in municipal and industrial wastewater treatment. Aeration is part of the secondary treatment process. Aeration in an activated sludge process is based on pumping air into a tank, which promotes the microbial growth in the wastewater. The microbes feed on the organic material, forming flocs that can easily settle out. After settling in a separate settling tank, bacteria forming the “activated sludge” flocs are continually circulated back to the aeration basin to increase the rate of decomposition.
How does Aeration Work?
The bacteria in the water require oxygen for the biodegradation process to occur. Aeration provides oxygen to bacteria for treating and stabilizing the wastewater. The bacteria in the wastewater break down the organic matter containing carbon to form carbon dioxide and water utilizing the supplied oxygen. Without sufficient oxygen, bacteria are unable to biodegrade the incoming organic matter in a reasonable time.
In the absence of dissolved oxygen, degradation must occur under septic conditions that are slow, odorous, and yield incomplete conversions of pollutants. Under septic conditions, some of the biological process converts hydrogen and sulphur to form hydrogen sulphide and transform carbon into methane. Other carbon will be converted to organic acids that create low pH conditions in the basin and make the water more difficult to treat and promote odour formation. Biodegradation of organic matter in the absence of oxygen is a very slow biological process.
There are two common types of water aeration: subsurface and surface.
What is Subsurface Aeration?
Subsurface is the most common type of aeration. Large wastewater treatment plants in urban areas commonly use it. Subsurface aeration uses porous devices that are placed below the liquid’s surface. These diffusers or submersible aerators are lowered into the water or fluid and compressed air is released, creating bubbles. This method delivers the most oxygen available into the water and ensures the water and oxygen are thoroughly mixed.
What is Surface Aeration?
Surface aerators push water from under the water’s surface up into the air, and then the droplets fall back into the water, mixing in oxygen. The jets of water break the surface with varying degrees of force.
Why is Aeration Important for Wastewater Treatment?
Aeration is the most critical component of a treatment system using the activated sludge process. When properly implemented, aeration also eliminates seasonal problems such as algae growth or stratification. When exposed to heat and sun, still bodies of water such as reservoirs become stratified. This causes problems, such as foul odors, weed and algae growth, and fish kills. By improving the nutrient-oxygen balance, aeration helps improve water quality. A well-designed aeration system has a direct impact on the level of wastewater treatment it achieves. An evenly distributed oxygen supply in an aeration system is the key to rapid, economically viable, and effective wastewater treatment.

Energy Audit – An Overview

Energy Audit is the first step in Energy Conservation and Energy Efficiency Projects for Industrial Plants. Energy Audit is a periodic exercise undertaken by a plant to assess its energy consumption and identify opportunities for Energy Conservation and Energy Efficiency. It also helps plant personnel in modernizing the plant with new technological solutions. It benefits plants cut down production costs.

In India, Energy Audit is quite popular in an Industrial or Commercial Facility. Many companies have realized the potential of energy saving in their plant. However one must realize that Energy Audit is only the first step in the direction of energy efficiency and energy conservation. The recommendations made as part of the energy audit have to be implemented to achieve the energy saving targets.

The energy saving recommendations doesn’t require much investment. In some high cases, the investment may be higher. The plant then takes up the investments in a phase-wise manner, which result in delayed energy saving for the plant. In fact the plant may never take some of the recommendations up. This renders the entire energy audit exercise futile.

Energy Audit works for every single Plant or Commercial Facility, as there is always scope for Energy Optimization through Energy Conservation & Energy Efficiency. Every plant goes through some changes over a period of time. Moreover an external Energy Audit team works across departments and brings in rich experience gained from Energy Audit of several plants. This not only results in gaining fresh perspective of Energy saving possibility by an external team also results in bench-marking based on similar parameters.

Energy Audit gives a positive orientation to Preventive Maintenance, Safety and Quality Control programs thereby improving the overall efficiency and output of existing system.

Nearly all the Industrial Units and Commercial Complexes have a potential to save 10-15% on Energy Bills and additional savings in Thermal Energy.

The evident reason why a plant goes for an Energy Audit is the saving of energy. This saving translates into monetary saving and hence can have a direct impact on profitability of a Company. It is also a step towards sustainability.

However, Energy Audits should look at a more comprehensive approach than just reducing cost. Industries should focus more on reducing their carbon footprint as necessitated by Governing Environmental Laws. Energy Audits must go beyond the conventional approach and adopt newer technologies for Green Power Generation.

With increased environmental awareness the pressure on Industries is mounting to reduce their Carbon footprint by adopting Greener Methods wherever possible. In such as scenario Energy Audit would play a crucial role in offering Industries a comprehensive approach towards a Greener Plant.

There is no specific answer as to how much energy a plant could save post an Energy Audit. An estimate could certainly be provided and in all cases Energy Audit could prove to be useful and economically viable. This is especially true in the present day scenario when Energy costs are ever rising and are expected to rise further.

Each Industrial Plant must carry out Energy Audits for reducing their energy usage by adopting energy conservation and energy efficiency measures.

Temperature Mapping for Pharmaceutical Industry

Temperature mapping is important for verifying the efficacy of temperature controlled storage systems such as cool rooms, fridges and warehouses. It is vital for businesses that work with temperature sensitive products such as pharmaceuticals or warehouses.

The process of mapping outlines the differences and changes in temperature that occur within a single temperature controlled system. This is due to influences like opening doors, proximity to cooling fans, personnel movement, and the quantity of products being stored at any given time. Temperature mapping locates the points of greatest temperature fluctuation and difference then analyses the causes of these. Conditions are created to verify that a system maintains the correct temperature in all situations when influenced by external factors such as weather and internal factors such as airflow restrictions and the operation of the Heating, Ventilation and Air Conditioning systems. The effects in difference of temperature are calculated to ensure the systems meet industry standards.

The temperature of different spaces within cooling rooms, industrial fridges and other controlled temperature environments can vary by up to 10°C. Generally, the central space within a chamber maintains constant temperature, however the corners and areas surrounding the fans will fluctuate. External seasonal weather must also be taken into account especially for warehouses.

Temperature mapping is important for businesses and organisations dealing with temperature sensitive products, like biochemical products such as medications and vaccines. Verifying that the refrigeration systems maintain an acceptable temperature level for each specific product at all times is what temperature mapping is all about, and this is supported using ongoing monitoring systems.

Once mapping has established where temperature variation points lie within the control system then monitoring can be installed. It is important to re check any back up systems to be sure that the chambers will work in other circumstances.

Different mapping equipment gives different results. It is important to ensure that the equipment being used has sufficient accuracy ratings to give reliable data. For example, better equipment will provide readings that are accurate within plus or minus 0.3°C, whereas budget equipment may only have accuracy ratings of within 2.0°C. For products that must be stored within a limited temperature range, this budget equipment cannot provide sufficiently specific temperature data.

Warehouses must have information regarding the building’s external conditions, as it is vital for effective mapping and monitoring. Warehouses are generally mapped for a full year to ensure all external conditions are accounted for in the data. This also helps to determine placement of monitoring systems due to influence of external conditions.

Temperature-controlled rooms such as fridges or cold rooms can be mapped once as their external environment is controlled. However, it is advisable to make sure that other external forces that could change their temperatures significantly do not heavily influence the HVAC systems of these buildings or environments. The mapping in warehouses should take into account the fluctuation in the warehouse temperatures and conduct the tests during its most extreme levels.

Load testing is important aspect of the temperature mapping process. It investigates how expected product levels interact with individual temperature controlled chambers. This testing takes into account whether the product will arrive in the required condition or if cooling is necessary. Testing should verify whether the chamber could cope with the maximum specified load arriving all at once to then be cooled. If it can operate properly in this situation, as well as operating effectively at full capacity, the chamber can be considered sufficiently load tested. It is also advisable to test the system’s performance by simulating failures, to ascertain whether the system could be used even while experiencing some equipment failures.

Once the mapping process has been completed, sensors should be installed to allow for continued surveillance of the areas that have been identified as being most influenced by temperature change. The stable areas should be monitored to help with any troubleshooting.

Monitoring systems should be planned and documented according to the scientific rationales shown by the temperature mapping procedure. This development strategy should then be reviewed and approved by the system owners as well as by an independent quality unit before being installed. Sensors should be placed around the products, around major potential temperature influences such as doors and cooling fans, and at different heights, especially in larger chambers.

Sensor equipment can be split into zones according to the area affected by similar influences. For example, in a square or rectangular chamber, the zones in corners away from doors will behave much the same as each other, as will the zones adjacent to doors or fans. If the monitoring devices are zoned, data can be compared to provide overall information on how the system usually functions.

To summarize, temperature mapping provides information on warmer and colder areas within temperature-controlled environments. They supply details on the overall operation of the systems. After temperature mapping a system, monitoring equipment can be installed to provide real-time feedback on system operations and its stability for product protection.

Process Engineering: An Overview

Process Engineering focuses on design processes, operation, process control, and process optimization. This discipline of engineering may focus on physical, chemical, or biological processes. Process engineering encompasses a large array of different industries and sectors. It has a wide range of applications, considerable potential value, and diverse methods.

Process engineering, as a discipline, can be traced back to the era of the 60s, when the term was first coined. However today, this engineering field has gained popularity across the globe. Numerous companies offer Process Engineering services. It is an active area for research, study and application. Process engineering has effected positive change on a global scale.

Since Process Engineering has a broad range of applications in various industries and sectors, the specifications in analysis varies with each sector. Process engineering have various sub-disciplines. Experts usually specialize in one or two of these sub- disciplines.

Process Design – Process design looks at the way the process in question has been designed and set up. It looks for ways to improve this design and structure, and may utilize hierarchical decomposition flow sheets, attempt superstructure optimization, or study plants with multi-product batches. Poor, inefficient design and structure elements can then be removed and substituted with design components that optimize the system better.

Process Operations – Process operations looks at the way the process in question is being executed. It may incorporate real-time optimization or fault diagnosis in an effort to improve operations efficiency. It may also study the operation’s schedule and examine multi-period planning, and other relevant data.

Process Control – Process control concentrates on the reliability of the process. It often employs tools such as controllability measures, robust control, model predictive control, statistical process control, and process monitoring to name just a few. By improving control over the process more consistent, dependable results are gained.

Supporting Tools – Supporting tools in process engineering focuses on the ancillary tools and systems that help support the primary process. These tools may include things such as equation based process simulation, AI or expert systems, sequential modular simulation, global optimization, large-scale nonlinear programming (NLP), optimization of differential algebraic equations (DAEs), and mixed-integer nonlinear programming (MINLP). These supporting tools enhance the overall productivity and quality of the process.

Process engineering is beneficial to industries in various ways. They include everything from debottlenecking certain key problem areas, improving production speed, eliminating unneeded steps from a process, making the process or system safer, and increasing the quality, consistency, and/or volume of output. By and large process engineering provides a way for industries to reduce their costs while increasing the overall efficiency of their processes.

Process engineering has an incredibly far-reaching impact and potentially holds promise for nearly any industrial or commercial business. It is also at the forefront of expanding what is possible in the sciences and technology sectors. Some particular industries served by process engineering include:

  • Chemical
  • Petrochemical
  • Refining
  • Food and food processing
  • Manufacturing
  • Mineral processing
  • Medical
  • Pharmaceutical
  • Bio-techs
  • Biomedical
  • Textiles
  • Transportation

Process engineering is a fast-paced, dynamic discipline that is continually evolving and pushing the envelope of what is possible. Panorama provides a thorough professional service that covers each step of process engineering. With roots in Chemical and Pharmaceutical industry, Panorama provides the best service.

6 simple marketing steps for your Chemical/Pharma Industry

Who says good projects don’t require marketing? Good project deserves intelligent marketing. However, there are many risks involved in marketing especially for a first timer. To achieve genuine success, one must take risks and move out of their comfort zones. Constructing a marketing plan is easy but constructing one that will effectively help your business grow requires critical thinking and strategy. It is important to understand the steps required to create and implement a plan. Any marketing strategy must be well articulated and thoroughly analyzed.

The process to attain the right kind of marketing is long and tiresome; we’ve narrowed it down for you. Here are six points to keep in mind for effective marketing communication.

  1. Small budget
    Just like your construction budget, compute a marketing budget. Don’t be exorbitant start small. Formulate a budget keeping in mind your revenue, marketing plan and competition. Don’t spend too much or too little. Setting a budget will give you a much clear picture on what you’re willing to invest in.
  2. Know your audience
    Conduct client experience surveys in the middle of your project. Obtain feedback from old clients. Testimonials make for great advertising. Not only will this help with prospective clients but can also aid in providing better services and recovering from any problems. Client surveys are helpful, especially, for residential projects.
  3. Core Idea
    Have one central idea. Every brand in the market stands for a value. List down the qualities you want your brand to be known for. Think of your brand as a person and associate it with a personality. Your brand must have a holistic approach. Exploit this core idea in all your marketing collaterals thereafter.
  4. Be creative
    Construction can be fun too. Just as you provide project management services, hire a team of marketing professionals that will guide you through this process. Nobody knows better than an expert. Allow them to take the risks and explore the creative elements hidden in your project. The ultimate goal should be to stand out and be different.
  5. Digital Marketing
    Go digital! The first step in the digital stage is to develop a website. Then you move on to social media. Not only is this a great place to connect with prospective clients but also helps you stay in touch with the old ones. Give your clients a platform to share their experiences.
  6. Monitor the results
    Your marketing plan may be brilliant but it is always better to make sure your efforts are being paid off. Once your marketing campaign kicks off, check whether the campaign is working with the audience or not. Monitor feedback, check statistics, and compare results from previous years.

You may be the best in your field but competition is always running alongside. In this day, making your brand known is vital. The right kind of marketing will help you reach there. However, it is vital to steer clear of the risks that come along with marketing. A well-constructed and thoughtful marketing plan will assist your business in markets with a competitive edge.